13 replies to this topic

[DrSlamastika]

I want set the large lasers on both torsos sides at very top hardpoint.

From down: medium laser, medium laser and on the top large laser.
But I can do this only with left side torso.
Right side have some bugg and every time when I want set up large laser top, it change position it to in the middle point

Before it was ok, but now its fokd up. And when I was trying this scheme with small laser with large at top it workd, but not for medium laser.

Anyone else with similar porblem??

[DrSlamastika]

foking **** UI, I want put that fokin large lasers on top, but this stupid game still set it to middle. Why?

[Deathlike]

It's "automatic" and "working as intended".

People have asked for finer control over this especially with missiles and their tube limits, and that's not happening.

[Warrax the Chaos Warrior]

Same problem with the ON-1K. If you put a PPC and a laser in the arm, it will automatically move the PPC to the small, outer housing and the laser to the large, inner housing. It isn't just a cosmetic issue, it has an effect on the convergence mechanic and forces you to come a little further out of cover to shoot.

[DrSlamastika]

But before it was OK, I had Large lasers on top, but I was trying some new setup and when I was putting old setup back its just dont work . . .

And it suck cose I want sniping laser on the top? This is not just cosmetic issue.

[DrSlamastika]

For better understand, I had it like that yesterday.

Right arm: medium laser, left arm: AC10 and both torsos: medium laser, medium laser, large laser ( from down )

Today I was trying some setup with gauss gun and change some hardpoints, now I want go with old setup and cannot do it again like it was before. I really dont get it

[Reza Malin]

I too have had this problem, could do with a way to select each individual hardpoint.....

[WVAnonymous]

DrSlamastika, on 18 October 2013 - 02:12 PM, said:

For better understand, I had it like that yesterday.

Right arm: medium laser, left arm: AC10 and both torsos: medium laser, medium laser, large laser ( from down )

Today I was trying some setup with gauss gun and change some hardpoints, now I want go with old setup and cannot do it again like it was before. I really dont get it

Have you tried doing the load with no medium lasers, saving it, and going back in and adding them? Or the other way around, I can't tell which order you were trying to force.

[DrSlamastika]

I tried everything

[Otto Cannon]

http://www.reddit.co...g_weapon_order/

This is apparently a way around it.

Edited by Otto Cannon, 18 October 2013 - 07:59 PM.

[DrSlamastika]

THANK YOU man I will try it

[DrSlamastika]

Its working, thanks a lot again

[RandomLurker]

Otto Cannon, on 18 October 2013 - 07:58 PM, said:

http://www.reddit.co...g_weapon_order/

This is apparently a way around it.

Tested and update.

You don't have to purchase the weapon for it to work. All that's needed is for there to be 0 in your inventory after you mount the one you want. This means you can stash excess weapons on other mechs, if you have them, and get them off later.

[Laniarty]

RandomLurker, on 19 October 2013 - 09:46 PM, said:

Tested and update.

You don't have to purchase the weapon for it to work. All that's needed is for there to be 0 in your inventory after you mount the one you want. This means you can stash excess weapons on other mechs, if you have them, and get them off later.

Hmm, trying it that way didn't work for me. I had to purchase the weapon for the housing to reset.