10 replies to this topic

[Jazzbandit1313]

anyone? id like to stick to an XL300 or the STND 280 please

[Psikez]

How experienced are you? http://mechromancer....1,0,1,0,0,0,0,0

this is my trolololo build

edit: oops got your engine request mixed up, updated

I'll admit I'm not terribly familiar with the 1X build, usually would rather run an ilya or a 3D but

http://mechromancer....1,0,1,0,0,0,0,0

something of a more balanced loadout, ER PPC/UAC for range and UAC/MLAS for up close. Might want to shove the PPC on the other side of the mech to take advantage of the standard engine. I'm use to having all the heavy hitting weapons on the right side of the mech and using the left side as a shield though.

And one more: http://mechromancer....0,0,1,0,0,0,0,0

Although if you'd care to utilize a larger engine you can swap the XL300 for a 325 with endo and maintain all the heat sinks

Edited by Psikez, 07 June 2013 - 04:14 PM.

[Jazzbandit1313]

Psikez, on 07 June 2013 - 04:04 PM, said:

How experienced are you? http://mechromancer....1,0,1,0,0,0,0,0

this is my trolololo build

edit: oops got your engine request mixed up, updated

whats the heat efficiency on that

[El Bandito]

4 LLasers build is my all time favorite.

[DevlinCognito]

The 5 gun is one of my all time favourites. 5 Large Lasers is good if you can hang jusy behind a friendly assault that can punch holes for you to fill with hot laser loving! The two arm mounted in one group, torso in another & all 5 chained in a 3rd can help you control that heat well.

[Johnny Reb]

Well, I either have really good or really bad matches with the second one I will give you. Just configured the first today haven't tested yet:

http://mwo.smurfy-ne...586a3b79620f97b
one I run:
http://mwo.smurfy-ne...254ff1a201abbcb

Also this is a very low mech in my current stable of 28. (with around 35 mastered, just sold and not this one working at master, slowly)

[Psikez]

Jazzbandit1313, on 07 June 2013 - 04:09 PM, said:

whats the heat efficiency on that

Not good, I don't recall off-hand but I believe around .9 or 1.0 but I have not played that build post PPC heat reduction.

You will get 2 full alphas before your in overheat territory (with 2x efficiencies anyway) With that XL I would not take an overheat shot like a stalker unless its a matter of life or death. You don't have the armor or profile to deal with getting primaried while standing still

The 5 LL one is generally quite popular and a few in my unit swear by it.

Johnny Rebs 5 LL design pretty much pushes everything to the limit. Quite a fine design.

Edited by Psikez, 07 June 2013 - 06:27 PM.

[Johnny Reb]

Thank you! It is not for me but I like to min/max, for better or worse!

edit: Coolant flush is standard!

Edited by Johnny Reb, 07 June 2013 - 07:45 PM.

[Deathlike]

Johnny Reb, on 07 June 2013 - 05:24 PM, said:

Well, I either have really good or really bad matches with the second one I will give you. Just configured the first today haven't tested yet:

http://mwo.smurfy-ne...586a3b79620f97b

Improved it slightly - used FF (since it was applicable) and used the tonnage savages to increase the engine and add another DHS with some slight armor loss
CTF-1X

[Ghostrider0067]

I've been running a PPC heavy build as of late but may end up trading one of them out. As of now, it goes like so:

2x PPC RA
1x ER PPC RT
1x ML LT
1x ML LA

I've not played all that much and need to find a nice sweet spot for the loadout. Perhaps I'll go LL instead of the two standard PPCs. We'll see.

[Johnny Reb]

Deathlike, on 08 June 2013 - 11:12 AM, said:

Improved it slightly - used FF (since it was applicable) and used the tonnage savages to increase the engine and add another DHS with some slight armor loss
CTF-1X

Would do this, if I wasn't prolly going back to my 5 LL setup.