I was in River City and had targetted a distant Hunchback. With the zoom module, I was suffering from double vision. I saw two target boxes, each on a Hunchback, and two thermal signatures. I did not have time to hit the video capture, so I don't know what was going on.
1
3 replies to this topic
#1
Posted 05 February 2013 - 05:52 PM
#2
Posted 05 February 2013 - 09:30 PM
I have experienced a similar problem where the target box does not appear over the target when I enter Advanced Zoom mode, and then move my torso/view a small to moderate amount. The target box stays in the location as if the Zoom mode were never entered.
This is a bug that occurs almost every time I use the Zoom module, and it seems to be to a greater degree than the general bug at http://mwomercs.com/...-around-target/
This is a bug that occurs almost every time I use the Zoom module, and it seems to be to a greater degree than the general bug at http://mwomercs.com/...-around-target/
#3
Posted 15 February 2013 - 12:42 PM
RenegadeMaster, on 05 February 2013 - 09:30 PM, said:
I have experienced a similar problem where the target box does not appear over the target when I enter Advanced Zoom mode, and then move my torso/view a small to moderate amount. The target box stays in the location as if the Zoom mode were never entered.
This is a bug that occurs almost every time I use the Zoom module, and it seems to be to a greater degree than the general bug at http://mwomercs.com/...-around-target/
This is a bug that occurs almost every time I use the Zoom module, and it seems to be to a greater degree than the general bug at http://mwomercs.com/...-around-target/
I have exactly the same problem with advanced zoom.
Edited by czermy, 16 February 2013 - 02:30 PM.
#4
Posted 17 February 2013 - 10:37 AM
Niko Snow, on 11 February 2013 - 12:53 PM, said:
Please send us a screen or video capture of this issue to support@mwomercs.com
Thanks!
Thanks!
Shortly after my original post, I contacted support with the below bug. In case the request number is needed for re-tagging this thread, it is 68045. I have since replied to that support request with links to the videos (thanks czermy!)
RenegadeMaster, on 06 February 2013 - 03:28 PM, said:
This has been logged with Development (thanks Magius!)
Here are the details that I wrote up for it:
Steps to Replicate:
1) Launch with any mech with the Advanced Zoom module equipped
2) After the match starts, find a non-ECM enemy gets in visual/radar range.
3) Target the mech using the R key.
4) Enable Advanced Zoom mode.
5) With the mech visible within the Zoom box, move the mech torso left or
right considerably, but not so far that the mech is outside the Zoom box.
Expected result:
Target box appears around the mech.
Actual result:
Target box does not appear around the mech. The target box appears on the
screen in the same location as if the Advanced Zoom module was not enabled.
Here are the details that I wrote up for it:
Steps to Replicate:
1) Launch with any mech with the Advanced Zoom module equipped
2) After the match starts, find a non-ECM enemy gets in visual/radar range.
3) Target the mech using the R key.
4) Enable Advanced Zoom mode.
5) With the mech visible within the Zoom box, move the mech torso left or
right considerably, but not so far that the mech is outside the Zoom box.
Expected result:
Target box appears around the mech.
Actual result:
Target box does not appear around the mech. The target box appears on the
screen in the same location as if the Advanced Zoom module was not enabled.
2 user(s) are reading this topic
0 members, 2 guests, 0 anonymous users