Jump to content

What's The Best Build For A Kodiak 1?


89 replies to this topic

#81 Magnus Santini

    Member

  • PipPipPipPipPipPipPip
  • The Tip of the Spear
  • The Tip of the Spear
  • 708 posts

Posted 08 February 2017 - 07:22 AM

http://allrecipes.co.../big-bear-stew/ Posted Image

#82 TercieI

    Member

  • PipPipPipPipPipPipPipPipPipPip
  • Littlest Helper
  • Littlest Helper
  • 8,164 posts
  • LocationThe Far Country

Posted 08 February 2017 - 07:24 AM

View PostSnazzy Dragon, on 08 February 2017 - 06:44 AM, said:


But muh 2 ton overheating piece of **** jumpjets


Hey, you want to run a 92-ton hardpoint starved mech that can leap small pebbles in a single bound instead of a proper Kodiak, don't let me stop you! ;)

(And it's still way better than the 1&5)

#83 Cerulean Knight

    Member

  • PipPipPip
  • Guardian
  • Guardian
  • 89 posts
  • LocationWisconsin

Posted 08 February 2017 - 07:27 AM

Yay for necro threads.

But, if you have some good fire control, I find this config works the best for me:

http://mwo.smurfy-ne...a27a7d3d97988a3

Might not be everyone's cup, but I love it. I have a similar config for my Nova (8 ERML), so I have some experience in handling the heat load. If you can handle the heat curve, it handles well and it can even give Kodiak-3s a source of panic from afar and up close.

Edited by Cerulean Knight, 08 February 2017 - 07:27 AM.


#84 XX BURT XX

    Member

  • PipPip
  • Bad Company
  • Bad Company
  • 32 posts

Posted 08 February 2017 - 11:12 AM

Thanks guys. I see a lot of you have troubles with this variant, I think I will perhaps give it a pass and try some other mech for laser build, a heavier broher for my Nova.

#85 Hanky Spam

    Member

  • PipPipPipPipPipPip
  • Ace Of Spades
  • Ace Of Spades
  • 202 posts

Posted 08 February 2017 - 01:46 PM

I've equipped the KDK-1 with 8 MPLs and a TC7.
It's a bit short on range, but within the MPL range it's deadly as ****.

#86 XX BURT XX

    Member

  • PipPip
  • Bad Company
  • Bad Company
  • 32 posts

Posted 09 February 2017 - 12:11 AM

View PostHanky Spam, on 08 February 2017 - 01:46 PM, said:

I've equipped the KDK-1 with 8 MPLs and a TC7.
It's a bit short on range, but within the MPL range it's deadly as ****.


Can you tell me how many times are you able to fire before overheat? Not alpha, I think firing 4xleft and later 4x right side MPL is preffereble.

#87 The Unstoppable Puggernaut

    Member

  • PipPipPipPipPipPipPipPip
  • The Grizzly
  • The Grizzly
  • 1,022 posts
  • LocationLondon

Posted 09 February 2017 - 12:21 AM

So much grief for this mech, thanks Hanky Spam.

I've settled on 6 med pulses and one PPC and TC1. That way I've got all ranges covered, get to keep the 400xl and flood the chassis with heat sinks.

#88 Hanky Spam

    Member

  • PipPipPipPipPipPip
  • Ace Of Spades
  • Ace Of Spades
  • 202 posts

Posted 09 February 2017 - 01:46 AM

View PostXX BURT XX, on 09 February 2017 - 12:11 AM, said:


Can you tell me how many times are you able to fire before overheat? Not alpha, I think firing 4xleft and later 4x right side MPL is preffereble.


I'am not exactly sure anymore and cannot test it right in this moment (can edit the results later), but I think it was 3 or 4 times until you overheat. You shouldn't forget that both arms have an alpha of 32 dmg.
So in a very short time-frame you can do almost instantly 64 dmg and more.
The highest damage that I scored with this setup was 1172 on mining collective. I would call this a viable build, though it's limited to some degree due to range...

#89 JudauAshta

    Member

  • PipPipPipPipPipPip
  • Big Brother
  • Big Brother
  • 264 posts

Posted 09 February 2017 - 02:04 AM

best build for kodiak 1 is selling it and buying kodiak 3

#90 chucklesMuch

    Member

  • PipPipPipPipPipPipPipPip
  • Shredder
  • Shredder
  • 1,424 posts
  • Google+: Link
  • LocationNew Zealand

Posted 09 February 2017 - 10:58 AM

In solo queue I went with:
1x lbx20
2x srm6a
4x mpl - (8spl is most likely the better option but mpl worked better for me)
Xl 400





13 user(s) are reading this topic

0 members, 13 guests, 0 anonymous users